Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Puyallup: What to Know First

We provide independent Olympia Chimney chimney cap and crown service in Puyallup, with most repairs quoted and scheduled within 48 hours of your call. A standard Olympia Chimney cap replacement runs $340-$680 installed; crown repair or coating typically falls between $450-$1,200 depending on accessibility and whether the flue surround needs rebuilding. Every job starts with a camera inspection, a written price, and your approval before any work begins.

Call (253) 323-5667

This page is for homeowners in Puyallup, South Hill, and the surrounding Pierce County area who have an Olympia Chimney cap or crown showing rust, cracks, or water intrusion and want to know what it actually costs, what parts fit, and whether the repair can wait. If you’re seeing water stains on the ceiling near your fireplace, hearing metal rattling in windstorms, or noticing mortar flaking from the crown, call us at (253) 323-5667. We’ll run the camera, show you what we found, and write down the price before we touch a tool.

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney stainless single-flue caps (SC series): The SC-1318 and SC-1824 are common in Puyallup’s 1980s-2000s ranch builds, and we’ve replaced dozens where the 304-grade mesh has rusted through at the welded corners after 8-12 years of marine-influenced moisture. The salt air coming off Puget Sound accelerates pitting where the mesh meets the lid. We match the flue dimension exactly, and when the original spec is discontinued, we source equivalent 316-grade aftermarket through our Haven buying network with Olympia Chimney’s published dimensional specs.
• Olympia Chimney galvanized multi-flue caps (MC series): The MC-913 and MC-1117 carry a 20-year warranty but we’ve found the galvanized skirt on early production runs (pre-2018) delaminates in the South Hill corridor where roof pitch and tree cover trap humidity against the chase. The skirt separates from the frame, creating a gap that funnels water directly onto the crown instead of shedding it. We document this with the camera from inside the flue, then replace with a stainless equivalent or apply a crown rebuild beneath a new cap if the concrete is spalled.
• Olympia Chimney outside-mount caps (OM series): The OM-1318 and OM-1824 attach to the chimney exterior rather than the flue tile, which puts the mounting tension on crown concrete that may already be compromised. In Puyallup’s freeze-thaw cycles, we’ve seen the lag bolts work loose as the crown develops hairline cracks, tilting the cap and creating a reverse slope that pools water. We remove the cap, assess the crown integrity with a hammer test and camera survey, then either reseat on rebuilt concrete or convert to a flue-mount system if the crown is too far gone.
• Olympia Chimney draft-increasing caps (DC series): The DC-913 and DC-1117 use a turbine-style lid that seizes when grease-laden smoke from poorly seasoned wood coats the bearing. Puyallup’s abundant Douglas fir, if burned green, accelerates this. The frozen turbine creates a downdraft instead of solving one. We disassemble, clean the bearing race, and quote replacement only when the housing itself is warped from overheating. Most owners don’t realize the cap needs annual cleaning same as the flue.
• Olympia Chimney crown wash failures beneath any cap: Olympia Chimney does not manufacture crown material, but their cap warranties require a “sound chimney structure” which many Puyallup homeowners interpret as the cap alone. We’ve pulled caps off crowns where the wash was eroded to aggregate, finding the cap was doing all the water-shedding until it couldn’t. The camera shows the interior flue tile joints gapped from water saturation. We rebuild with a proper Portland-based crown mix, slope it 2:12 minimum, and install a new cap with a 2-inch overhang - the detail that prevents recurrence.

Our Olympia Chimney Chimney Cap & Crown Process

1. 1
   Camera inspection first. We run a full NFPA 211 Level 2 scan down every flue served by the chimney, documenting the flue tile condition, smoke chamber profile, and any water intrusion patterns. Corrine Halstead’s rule: camera goes in first, price gets written down second, work starts third.
2. 2
   Cap removal and dimensional verification. We pull the existing Olympia Chimney cap, measure the flue tile or chase opening to the sixteenth, and check for discontinued series numbers. If your SC-1318 is out of production, we cross-reference the Haven parts catalog for dimensional equivalents from Olympia Chimney, Famco, or Gelco.
3. 3
   Crown assessment and repair scope. We hammer-test the crown, map crack patterns, and determine whether a surface coating (HeatShield CrownCoat or equivalent), partial rebuild, or full pour is warranted. The written scope specifies material, thickness, and slope before we mix anything.
4. 4
   Parts procurement through Haven network. We source replacement caps through our buying agreement with Olympia Chimney distributors and backup suppliers - DuraFlex for liner-adjacent work, Gelco for custom dimensions, HeatShield for crown resurfacing. This keeps pricing honest and avoids the markup of single-source ordering.
5. 5
   Installation, documentation, and testing. We install to manufacturer torque specs, seal with high-temp silicone at the flue tile interface, and run a final camera pass to confirm no debris dropped and the flue is unobstructed. You receive dated photos, the written warranty, and the Haven Standard Clause 4 photo record archive.
6. 6
   365-Day Done Right Promise activation. If water intrudes, the cap shifts, or the crown cracks through our repair, we return and make it right. The promise is stamped on every invoice under Haven Standard Clause 5.

Before

After

What Olympia Chimney Chimney Cap & Crown Costs in Puyallup

These are installed prices, including the camera inspection and photo documentation. We do not charge separately for the diagnostic. If a competitor has given you a written estimate, bring it - our Free Second Opinion applies to Olympia Chimney work same as any other brand. Call (253) 323-5667 for a written quote; estimates are free and we do not start work until you have the price in hand.

Why Puyallup Homeowners Call Level Two Chimney Puyallup for Olympia Chimney Work

We’ve inspected and cleaned more than 38,000 chimneys since 2009, and a growing share of our Puyallup calls involve Olympia Chimney products installed in the 2010s building boom. Our techs carry the dimensional catalogs for discontinued SC and MC series, so you’re not waiting a week for a parts search while water keeps coming in.

Every technician is background-checked, uniformed, and assigned by name - you’ll get a text when they’re en route, per Haven Standard Clause 2. The camera scan and photo record are standard, not an upsell. And because we source through multiple suppliers including DuraFlex, HeatShield, Gelco, and Olympia Chimney’s distribution network, we can recommend the part that fits your actual flue, not just the part that’s in one warehouse.

Corrine Halstead has worked the South Hill corridor long enough to recognize when a rattling cap is the symptom and when it’s the crown beneath that’s the real problem. We don’t sell caps to cover failing concrete, and we don’t rebuild crowns that a quality coating would protect for another decade. The camera shows the difference, and the written price lets you decide without pressure.

FAQs