Gelco Chimney Cap & Crown Nationwide

Gelco Chimney Cap & Crown in Puyallup: What to Know First

We provide independent Gelco chimney cap and crown service in Puyallup, with most inspections scheduled within a week and repair work quoted in writing before we touch a tool. A Gelco cap or crown job typically runs $280-$850 depending on whether we’re sealing hairline cracks in a crown or replacing a multi-flue cap that has rusted through at the seams. This page is for homeowners who already know they have a Gelco product on their chimney and need to know what’s failing, what it costs, and who can fix it without voiding whatever warranty still applies.

Call (253) 323-5667

Call (253) 323-5667 for a free estimate. We answer live, 24 hours a day.

How Gelco Products Fail - and How We Fix Them

• Gelco Ultra-Flue caps with mesh blowout. The 5/8-inch spark arrestor mesh on Ultra-Flue series caps fatigues at the weld points after 6-10 years in Puyallup’s wet winters, especially on south-facing exposures where freeze-thaw cycles concentrate. We see this most often in the South Hill corridor where older installations used the original 304-grade mesh rather than the later 316 upgrade. We replace with matched 316 stainless mesh or source a full OEM cap if the frame itself has warped.
• Gelco Single-Flue caps with base rail rust. The stamped base rail on pre-2015 Single-Flue caps traps water at the chimney shoulder, accelerating galvanic corrosion where the rail meets the flue tile. In Puyallup, this shows up as orange staining on the brick course below the cap, sometimes mistaken for a crown leak. We pull the cap, assess the flue tile edge for spalling, and install a retrofit base with integrated drip edge that moves water clear of the masonry.
• Gelco Multi-Flue cap frame sag. The aluminum Multi-Flue caps (MC series) use a cross-braced lid design that can sag when debris loads up or when a homeowner walks the roof and steps on the center panel. The sag creates a ponding zone that backs water into the flue termination. We straighten or replace the lid panel, reinforce the cross-bracing with stainless gussets on larger spans, and document the flue draft reading before and after to confirm flow isn’t restricted.
• Gelco crown wash separation on chase pans. Gelco’s chase pan assemblies include a factory-applied crown wash that shrinks away from the flue collar over time, leaving a gap that funnels water directly onto the framing below. This is the failure we find most often during Level 2 inspections in Puyallup’s 1990s-era townhome clusters, where the original chase pans were Gelco spec. We grind back the failed wash, reseal with HeatShield CrownCoat or replace the entire chase pan if the metal has thinned.
• Gelco band-around-brick cap installations with mortar joint compromise. Earlier Gelco cap styles relied on a tension band and exterior mortar bedding rather than a flue-mount or outside-mount flange. The band squeezes the mortar joints, and in Puyallup’s clay-heavy soils where chimneys settle seasonally, those joints crack and the cap tilts. We remove the band system, repoint the compromised course, and reinstall with a proper flue-mount cap or a custom outside-mount frame that doesn’t load the brick.

Our Gelco Chimney Cap & Crown Process

1. 1
   Camera-first inspection. We run the chimney camera before we quote any cap or crown work. Corrine Halstead’s rule on every Gelco job: camera goes in first, price gets written down second, work starts third. The camera shows us whether the cap failure has already let water damage the flue liner or smoke chamber, which changes the scope entirely.
2. 2
   Parts identification and sourcing decision. We identify the Gelco series and model from existing markings or measurements, then decide OEM versus quality aftermarket. Gelco OEM caps are available through Haven’s buying network, but for discontinued series we fabricate matched replacements from Olympia Chimney or Famco components that maintain proper mesh spec and overhang dimensions.
3. 3
   Written scope and price delivery. Before any work begins, you receive a written price, written scope, and written warranty under Haven Standard Clause 1. No verbal estimates, no surprises when the tech is already on your roof.
4. 4
   Repair or replacement with documentation. We perform the cap or crown work, photograph every stage, and record final cap position and flue draft readings. Clause 4 of the Haven Standard requires a documented photo record on every job, running continuously since 2009.
5. 5
   Cleanup and 365-Day Done Right Promise activation. We haul off old materials, leave the roof and yard as we found them, and stamp your invoice with the 365-Day Done Right Promise. If it’s not done right, we make it right.

Before

After

What Gelco Chimney Cap & Crown Costs in Puyallup

These are the prices we actually write down for Puyallup homeowners, not teaser rates that change on site. Every estimate is free, and we offer a Free Second Opinion on any competitor’s written quote. Call (253) 323-5667 for your exact number.

Why Puyallup Homeowners Call Level Two Chimney Puyallup for Gelco Work

We’ve inspected and cleaned more than 38,000 chimneys since 2009, and a significant share of the cap and crown calls in Puyallup involve Gelco products from the 1990s and 2000s building boom. Our techs know the difference between a Multi-Flue MC-132 and an Ultra-Flue U-50 without climbing down to check the paperwork. When Gelco parts are back-ordered or discontinued, we source equivalent-spec materials through DuraFlex, HeatShield, Olympia Chimney, Famco, and Copperfield, keeping customer prices honest through Haven’s buying network rather than marking up scarce OEM inventory.

Background-checked, uniformed technicians carry license information on every page and every truck. You get a text when your tech is en route. Calls are answered by a live person, 24/7, not a voicemail tree. And every job, Gelco or otherwise, is backed by the 365-Day Done Right Promise and the full Haven Standard.

FAQs